Image

Torque Transduccers & Torque Sensors

We offer a range of rotary torque sensors and transducers to suit a variety of industrial applications including hydrogen powered cars, peristaltic pumps, bottle capping etc. Our standard range of torque transducers can measure torque from 10mNm up to 13000Nm. Watch our video for a brief introduction to our products. If you need assistance in choosing a torque sensor to meet the requirements of a specific application, please contract us.
Image

SGR510/520 Torque Transducer

TorqSense Digital rotary strain gauge series (SGR) torque transducers use non contact technology eliminating the need for noisy slip rings. The SGR510/520 series torque sensors are suitable for torque measuring, testing, feedback control of drive mechanisms and process control applications.

The SGR series transducers use modern strain gauge signal conditioning techniques to provide a high bandwidth low cost torque measuring solution with high overrange and overload capabilities.

Datasheet
Manual
Installation Guide
Transducer Communications Protocol
Transducer CAN Bus Interface Manual (SGR520)
Transducer DLL Programmers’ Guide (SGR520)
  • Transducers from 175mNm to 13000Nm
  • Large fully functional overrange capability of 250% (SGR520)
  • Minimal side and end load errors
  • Low linearity deviation of ± 0.05% FSD
  • Low hysteresis error of ± 0.05% FSD
  • Zero variation in torque signal with rotation (cyclic variation)
  • Non contact signal transmission, no slip rings to wear out
  • High digital sample rate of 4000 samples per second
  • Adjustable torque data smoothness, low pass filter (SGR520)
  • Speed measurement / Power computation
  • Wide power supply range 12-32 VDC
  • Compatible with ethernet gateway module
  • Lifetime Warranty

Datasheet
Manual
Installation Guide
Transducer Communications Protocol
Transducer CAN Bus Interface Manual (SGR520)
Transducer DLL Programmers’ Guide (SGR520)
Image

SGR530/540 Rotating Torque Sensors With Separate Electronics

TorqSense Digital rotary strain gauge series (SGR) torque meters offer a separate electronics module and use non contact technology eliminating the need for noisy slip rings. The SGR530/540 series torque testing equipment is suitable for torque measuring, testing, feedback control of drive mechanisms and process control applications.

Datasheet
Manual
Installation Guide
Transducer Communications Protocol
Transducer CAN Bus Interface Manual
Transducer DLL Programmers’ Guide (ORT240)
  • Transducers from 175mNm to 13000Nm
  • Large fully functional overrange capability of 250% (SGR540)
  • Separate digital electronics
  • Minimal side and end load errors
  • Low linearity deviation of ± 0.05% FSD
  • Low hysteresis error of ± 0.05% FSD
  • Zero variation in torque signal with rotation (cyclic variation)
  • Non contact signal transmission, no slip rings to wear out
  • High digital sample rate of 4000 samples per second
  • Adjustable torque data smoothness, low pass filter (SGR540)
  • Speed measurement / Power computation
  • Wide power supply range 12-32 VDC
  • Compatible with ethernet gateway module
  • Lifetime Warranty

Datasheet
Manual
Installation Guide
Transducer Communications Protocol
Transducer CAN Bus Interface Manual
Transducer DLL Programmers’ Guide (ORT240)
Image

ORT230/240 Optical Low Capacity Torque Sensor

The ORT 230/240 low capacity torque sensor offers an ideal means for precise dynamic measurement of rotary and static torque less than 100Nm and for bandwidths of up to 50Khz.

The new TorqSense ORT 230/240 torque sensors replace the E200 ORT series and feature all new electronics that have produced significant performance gains in resolution, frequency response, reduced sensor current consumption and faster digital data throughput.

Datasheet
Manual
Installation Guide
Transducer Communications Protocol
Transducer CAN Bus Interface Manual
Transducer DLL Programmers’ Guide (ORT240)
  • Low inertia – High Speed capability because electronics are not fixed onto shaft
  • Non contact/brushless measurement
  • High Bandwidth
  • 200% safe mechanical overload
  • Excellent noise immunity
  • Separate digital electronics
  • Operates both statically and dynamicall
    – clockwise/anti-clockwise
  • Any full scale torque can be specified within standard range: 10mNm through to 100Nm
  • Lifetime warranty

Datasheet
Manual
Installation Guide
Transducer Communications Protocol
Transducer CAN Bus Interface Manual
Transducer DLL Programmers’ Guide (ORT240)
Image

SIT 105/110/120 Series Strain Gauge Torque Sensors

Our SIT105/110/120 reaction torque transducers use modern wire foil strain gauge technology with the latest high performance stainless steel shafts. These reaction transducers are designed for operation in any industrial environment. Optional bench mount housing is available.

DataSheet
Instrallation Guide

Image

Ethernet Module (ENET-01)

The Ethernet Interface Module connects our range of Torque Transducers to a Local Area Network. By utilising existing structured cabling and infrastructure, our transducers become instantly accessible to any device on the network. Transducers can be accessed from any location within the premises where the structured cabling is present, or where it has been extended by wireless networking technologies. Furthermore, if the network is internet connected, or gateways and VPN’s are present, the transducers range can be extended without limit, enabling access and monitoring from literally anywhere.

Datasheet
Quick Start Guide
Image

ETD Transducer Display Interface

The Transducer Display ETD is a readout suitable for all SGR, ORT and RWT transducers. Although it is primarily used to display torque and peak torque, it can also display speed and power, provide access to the analog outputs from the transducer and connect the transducer to a PC for use with TorqView and the Transducer Control Program.

Datasheet
Manual
Image

TorqView Torque Monitoring Software

TorqView is an easy to use advanced torque monitoring software application available to operate in conjunction with the SGR520/540, ORT240, SIT120 Series Transducers to provide a flexible display, real time plotting and data recording facility.

DataSheet
Manual
Image

Bluetooth Interface

The optional Bluetooth interface box bring wireless flexibility to your TorqSense® transducers. The box simply plugs into the 15 way ‘D’ digital lead connector. It allows the transducer to be powered through the interface as well as providing a USB output.

DataSheet
Image

Torque Transducer Signal Breakout Unit

The SBU-01 Transducer Signal Breakout unit can be use with any Sensor Technology Torque transducer. The unit provides easy access to all the transducer functions including Analog outputs, RS232, USB and the optional CANbus. Users can also zero the transducer with the SBU-01, and it provides indication of transducer operational status.

Datasheet
Quick Start Guide